Belt Deflection Tool

Place the plunger end of the tension gauge on the top of the belt. Gates 91132 belt tension tester. Replacement for part 0744 098 arctic cat drive belt deflection adjustment tool 2016 2019 team models.

5691 3821 4995 6410 7268 5520 334 5732 2506 1816 9875 2606 9713 4677 386 5155 3189 5206 7783 2146 7179 4592 616 5587 4597 9076 5172 4127 5150 2600 5459 7637 3600 7 8418 4649 5189 670 3905 8028 4516 6597 568 311 8620 1836 998 1141 8331 6755 2666 4162 5929 1629 7130 5158 4413 6869 8568 5135 4057 353 2632 2194 4495 2263 3983 1504 1828 5350 2668 6203 5479 2468 2117 9751 1283 9513 1766 9985 5698 8606 7026 2431 4514 6159 846 5354 1333 8900 8048 5373 7904 8359 4333 5560 1350 8661 3078 3582 4782 1990 6229 8396 7751 295 6898 4563 5539 379 8601 1941 5848 3081 7711 890 1924 3839 3513 8842 7362 5523 3264 8089 6784 9433 4017 9832 6495 3849 3976 5400 4912 5084 6850 4330 5888 1874 5519 8711 7470 2226 8229 5061 4934 3562 8902 6701 1757 332 8460 2374 9089 1095 3392 3286 1802 5020 7804 8845 3858 6573 9197 7545 9285 3549 6896 5153 6974 8660 4395 236 7296 4659 2928 9235 2587 2339 8123 6917 211 4768 6738 4605 5146 9386 695 9093 5883 8651 3437 9430 5837 3069 4795 2081 3729 4523 4159

Belt Tensioner Belt Tension Measuring Tool Trummeter

Fenner Belt Tensioning Pen Bearings Online

Tension Gauge

Belt Tension Gauge Otc Tools

Belt Drive Accessory Belt Tension Checker

Belt Tension Tester Tool 40006 85 Harley Davidson Usa

Measure belt span t.

Belt deflection tool.

The skf belt frequency meter is one of the most accurate tools available for measuring the belt tension on a belt drive. 4 4 out of 5 stars 371. Improperly tensioned belts cause slippage squealing heat build up and premature failure. Financing offer available only on new harley davidson motorcycles financed through eaglemark savings bank esb and is subject to credit approval.

After a new belt has been installed run the engine for 3 to 5 minutes to seat the belt. The apr may vary based on the applicant s past credit performance. For belts wider than two inches a metal or wooden strip 3 4 to 1 inch wide should be placed across the belt between it and the tester to prevent distortion. Lift the plunger from the belt and read the pounds of force measurement at the o ring on the plunger.

Release the pressure on the gauge and read the measurement indicated by the small o ring in pounds of force required to deflect the timing belt. Otc 4748 belt tension tool 14 99 link to tool. Holding the tension gauge vertical to the belt press down until the bottom of the o ring on the plunger is even with the top of the wood. Get it as soon as tue dec 15.

Results are quickly achieved reliable and most importantly repeatable. If the measured force is less than the required deflection force lengthen the center distance. Deflect the timing belt until the bottom of the large o ring is even with the bottom of the straight edge. Krikit pocket gauge for v belts part number 93865.

Dayco belt tension gauges. Free shipping on orders over 25 shipped by amazon. This is commonly expressed as the amount of belt deflection that results when a measured force is applied at a specified point on the back of the belt. The fenner belt tension indicator is a simple tool that helps ensure accurate belt tension.

The tool is also extremely easy to use while minimizing the risk for human errors. Dayco engineers recommend careful belt tensioning. Then tighten belt so that it deflects 1 64 inch for every inch of belt span when a force as specified in the table below is applied to the top of the belt. For short centre distance drives where the deflection of the belt is too small to measure accurately it is recommended that both deflection and setting force be doubled.

Not all applicants will qualify. The chart enclosed with your tool lists deflection in millimeters mm and applied force in dekanewtons dan. Note many oem belt tightening specs are given in kg. 3 99 apr offer is available on new harley davidson motorcycles to high credit tier customers at esb and only for up to a 60 month term.